Tektronix TDS500C Manuel d'utilisateur Page 119
- Page / 148
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Specifications
TDS 500C, TDS 600B & TDS 700C Performance Verification and Specifications
2–3
general purpose knob to adjust some function, such as the position of measure-
ment cursors on screen, or the setting for a channel fine gain.
The user interface also makes use of a GUI, or Graphical User Interface, to make
setting functions and interpreting the display more intuitive. Some menus and
status are displayed using iconic representations of function settings, such as
those shown here for full, 250 MHz and 20 MHz bandwidth. Such icons allow
you to more readily determine status or the available settings.
Signal Acquisition System
The signal acquisition system provides four, full-featured vertical channels with
calibrated vertical scale factors from 1 mV to 10 V per division. All channels can
be acquired simultaneously.
Each of the full-featured channels can be displayed, vertically positioned, and
offset, can have their bandwidth limited (250 MHz or 20 MHz) and their vertical
coupling specified. Fine gain can also be adjusted.
Besides these channels, up to three math waveforms and four reference wave-
forms are available for display. (A math waveform results when you specify dual
waveform operations, such as add, on any two channels. A reference waveform
results when you save a waveform in a reference memory).
Horizontal System
There are three horizontal display modes: main only, main intensified, and
delayed only. You can select among various horizontal record length settings.
A feature called “Fit to Screen” allows you to view entire waveform records
within the 10 division screen area. Waveforms are compressed to fit on the
screen. See Table 2–2.
Both the delayed only display and the intensified zone on the main intensified
display may be delayed by time with respect to the main trigger. Both can be set
to display immediately after the delay (delayed runs after main mode). The
delayed display can also be set to display at the first valid trigger after the delay
(delayed-triggerable modes).
The delayed display (or the intensified zone) may also be delayed by a selected
number of events. In this case, the events source is the delayed-trigger source.
The delayed trigger can also be set to occur after a number of events plus an
amount of time.
GUI
- Technical Reference 1
- Digitizing Oscilloscopes 1
- 070-9874-02 1
- WARRANTY 3
- Table of Contents 5
- List of Figures 6
- List of Tables 8
- Product Damage Precautions 10
- Safety Terms and Symbols 10
- CSA Certified Power 11
- Symbols on the Product 11
- General Safety Summary 12
- Related Manuals 13
- Contacting Tektronix 14
- Performance Verification 15
- Procedures 15
- Input Channels vs. Model 18
- Conventions 18
- Brief Procedures 21
- Verify Pass 22
- Highlight Cal 22
- Functional Tests 23
- Signal Gnd 24
- Verify the Time Base 26
- Verify the Main and 27
- Delayed Trigger Systems 27
- Verify the File System 29
- Equipment Required 32
- TDS 600B Test Record 35
- TDS 600B Test Record (Cont.) 36
- TDS 500C/700C Test Record 39
- Check Offset Accuracy 43
- (Zero Setting) 43
- 0 V when the 44
- Check DC Voltage 45
- Measurement Accuracy 45
- Turn on the 48
- Check Analog Bandwidth 49
- Check Delay Between 54
- Channels 54
- terminator 55
- Time Base System Checks 59
- Trigger System Checks 61
- Check Accuracy 65
- Trigger-Level or 65
- Threshold, DC Coupled 65
- Set DC calibration generator 67
- Read results 67
- Sensitivity, Edge Trigger 69
- DC Coupled 69
- Sine Wave 70
- Generator 70
- Digitizing Oscilloscope 70
- To AUX TRIG INPUT 70
- Check if stable trigger 71
- Output Signal Checks 74
- Check output 76
- Check Probe 78
- Compensator Output 78
- Check Video Trigger 83
- Stop shows test complete 86
- Positive pulse 88
- Negative pulses 88
- 50 cable 90
- Signal Generator 90
- Filter Availability 103
- Reference Receiver 105
- Verification 105
- Performance Tests 112
- Specifications 115
- User Interface 118
- Signal Acquisition System 119
- Horizontal System 119
- Trigger System 121
- Acquisition Control 121
- On-Board User Assistance 122
- Measurement Assistance 122
- Digital Signal Processing 123
- Nominal Traits 125
- Warranted Characteristics 133
- Typical Characteristics 141
Produits connexes et manuels pour Mesure, test et contrôle Tektronix TDS500C
(46 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels